PIC18F2450/4450
DS39760A-page 180
Advance Information
2006 Microchip Technology Inc.
16.4
Operation in Power-Managed
Modes
The selection of the automatic acquisition time and
A/D conversion clock is determined in part by the clock
source and frequency while in a power-managed
mode.
If the A/D is expected to operate while the device is in
a power-managed mode, the ACQT2:ACQT0 and
ADCS2:ADCS0 bits in ADCON2 should be updated in
accordance with the clock source to be used in that
mode. After entering the mode, an A/D acquisition or
conversion may be started. Once started, the device
should continue to be clocked by the same clock
source until the conversion has been completed.
If desired, the device may be placed into the
corresponding Idle mode during the conversion. If the
device clock frequency is less than 1 MHz, the A/D RC
clock source should be selected.
Operation in the Sleep mode requires the A/D FRC
clock to be selected. If bits ACQT2:ACQT0 are set to
‘000’ and a conversion is started, the conversion will be
delayed one instruction cycle to allow execution of the
SLEEP
instruction and entry to Sleep mode. The IDLEN
bit (OSCCON<7>) must have already been cleared
prior to starting the conversion.
16.5
Configuring Analog Port Pins
The ADCON1, TRISA, TRISB and TRISE registers all
configure the A/D port pins. The port pins needed as
analog inputs must have their corresponding TRIS bits
set (input). If the TRIS bit is cleared (output), the digital
output level (VOH or VOL) will be converted.
The A/D operation is independent of the state of the
CHS3:CHS0 bits and the TRIS bits.
Note 1: When reading the PORT register, all pins
configured as analog input channels will
read as cleared (a low level). Pins config-
ured as digital inputs will convert as ana-
log inputs. Analog levels on a digitally
configured
input
will
be
accurately
converted.
2: Analog levels on any pin defined as a
digital input may cause the digital input
buffer to consume current out of the
device’s specification limits.
3: The
PBADEN
bit
in
Configuration
Register 3H configures PORTB pins to
reset as analog or digital pins by control-
ling how the PCFG0 bits in ADCON1 are
reset.
相关PDF资料
DSPIC30F3014T-20I/PT IC DSPIC MCU/DSP 24K 44TQFP
DSPIC30F3014T-20I/ML IC DSPIC MCU/DSP 24K 44QFN
PIC16LF819T-I/MLTSL IC PIC MCU FLASH 2KX14 28QFN
PIC16LF819T-I/SOTSL IC PIC MCU FLASH 2KX14 18SOIC
PIC18LF8410T-I/PT IC PIC MCU FLASH 8KX16 80TQFP
PIC18F2410T-I/ML IC PIC MCU FLASH 8KX16 28QFN
PIC18F2331T-E/SOG IC PIC MCU FLASH 4KX16 28SOIC
PIC18F4331T-I/ML IC MCU FLASH 4KX16 44QFN
相关代理商/技术参数
PIC16C55A-04/P 制造商:Microchip Technology Inc 功能描述:IC 8BIT CMOS MCU 16C55 DIP28
PIC16C55A-04/P 制造商:Microchip Technology Inc 功能描述:Microcontroller IC Number of I/Os:20
PIC16C55A-04/SO 功能描述:8位微控制器 -MCU .75KB 24 RAM 20 I/O 4MHz SOIC-28 RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16C55A-04/SO 制造商:Microchip Technology Inc 功能描述:8BIT CMOS MCU SMD 16C55 SOIC28
PIC16C55A-04/SP 功能描述:8位微控制器 -MCU .75KB 24 RAM 20 I/O 4MHz SPDIP-28 RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16C55A-04/SS 功能描述:8位微控制器 -MCU .75KB 24 RAM 20 I/O 4 MHz SSOP-28 RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16C55A-04E/P 功能描述:8位微控制器 -MCU .75KB 24 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16C55A-04E/SO 功能描述:8位微控制器 -MCU .75KB 24 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT